Rapid Joint® Drywall Setting Compound is a chemically activated setting-type joint compound with time-controlled hardening properties. Approximately 30% lighter than conventional setting compounds, it mixes lump free in as little as 30 seconds, spreads smoothly, feathers beautifully, and sands easily to produce a smooth-as-glass finish.

Rapid Joint is available in four different set times to meet the varied needs of drywall finishing professionals. All of the Rapid Joint Setting Compounds feature low shrinkage and exceptionally strong bonding.

 The Rapid Joint line is available in the following options:  
Rapid Joint® 20 Setting Compound (sets in 20 to 35 minutes)
Rapid Joint® 45 Setting Compound (sets in 30 to 60 minutes)
Rapid Joint® 90 Setting Compound (sets in 60 to 120 minutes)
Rapid Joint® 210 Setting Compound (sets in 3 to 5 hours)

Présentation du produit

Sélectionnez un filtre et cliquez sur Appliquer pour voir les résultats

Caractéristiques techniques

Information technique

Matériau : May contain calcium carbonate, perlite, mica, clay, synthetic or natural binders, thickeners, and calcium sulfate (gypsum).

Emissions: Asbestos free.

Couverture : Approximately 350 square feet per bag.

Setting time: Hardening times vary with type: Rapid Joint 20 will set in 20 to 35 minutes; Rapid Joint 45, in 30 to 60 minutes; Rapid Joint 90, in 60 to 120 minutes; and Rapid Joint 210, in 180 to 300 minutes. All are thoroughly dry in approximately 24 hours. Setting times will vary with conditions, such as temperature and humidity, but cannot be lengthened by adding water.

IMPORTANT : Maintain a minimum working temperature (air, material, water) of 45 degrees F (7 degrees C).

Stockage : Keep dry, avoid extreme temperatures, and close tightly when not in use; the product has an 18-month shelf life if protected from moisture (including humidity). Rapid Joint® is manufactured to conform to ASTM C475.

Caractéristiques techniques

Installation

Apply according to Gypsum Association (GA) publications GA-214 and GA-216.

Mixing Directions:
To mix the entire 18-pound bag: Place 1,25 to 1,50 gallons (4,6 to 6,0 liters) of clean, drinkable water in a plastic bucket, add the compound to the water, and mix thoroughly for 30 to 60 seconds. Scrape the sides of the pail frequently to ensure even mixing, and allow the mixture to stand for two to three minutes. Mixing may be done by hand or with a power-drill mixer as long as the compound is not overly mixed. If necessary, mix the compound another 30 seconds to achieve the desired consistency (water may be added in 4-ounce (100-milliliter) increments.
 

Remarque :
Mix only the amount that can be applied within the "working" time (that is, before the earliest possible setting time). Do not mix the compound with any other product or material.

  • Dirty water, overmixing, or extreme heat can accelerate set time.
  • Overdilution can reduce bond strength and will NOT delay hardening.
  • The mixing container and tools must be thoroughly cleaned between uses.
  • Set time will be accelerated should new batches of material come in contact with the residue of previous batches.

Prefilling:
Prefill imperfections, damaged areas, and large recesses where boards meet. Remove excess material. Allow to harden completely.

Finishing Joints and Corners:
La première étape : Apply a thin layer of compound to the tapered joint edge. Press the joint tape firmly into the compound (for inside corners, center-crease the tape) and tightly embed it with a finishing knife. Remove excess material. Apply a thin coat over the tape, nail/screw dimples, and corner beads/trim. For corner beads, extend the first coat at least 5 inches (125 millimeters) onto the panel. Let harden.
Deuxième étape : Apply a second coat over fasteners, joints, and trim, feathering the edges approximately 2.5 inches (65 millimeters) beyond the taping coat. For inside corners, allow one side to dry before second-coating the opposite side. Let harden completely.

Ponçage :
Light sanding (150-grit sandpaper or 220-grit mesh cloth or finer) may be done when the application is completely dry (after approximately 24 hours). Wet sanding is recommended to avoid dust.

Wallpapering:
Painting should not proceed until the joint compound is thoroughly dry (see GA-236). For best results, a good-quality gypsum-board primer should be applied, in accordance with the primer manufacturer's instructions, before painting or wallpapering.

Cleanup:
Rapid Joint® washes off easily with warm water. Tools should be dried thoroughly to prevent rusting.

Détails Garantie

Étant donné que les méthodes et les conditions d’application et de stockage, telles que la température, l’humidité et la dilution excessive sont hors de notre contrôle, CertainTeed Gypsum, Inc. (CertainTeed) ne sera pas responsable de la défaillance de ce produit lorsqu’il n’est pas utilisé et stocké conformément aux instructions et spécifications et aux normes de procédure acceptées inhérentes à l’application de cloisons sèches; ou lorsque l’utilisateur ne tient pas raisonnablement compte des conditions météorologiques et de travail défavorables. Cependant, si ce produit s’avère défectueux, la responsabilité maximale de CertainTeed sera limitée au remplacement du matériel défectueux uniquement ou au remboursement du prix d’achat initial. CertainTeed ne sera pas responsable des autres coûts ou dépenses. Il s’agit de la garantie exclusive et des recours fournis par CertainTeed, y compris, sans s’y limiter, les garanties implicites ou la qualité marchande, l’aptitude à l’emploi et l’aptitude à un usage particulier. Tout recours en garantie doit être soumis par écrit à CertainTeed dans les 30 jours suivant la découverte du problème. Les lois nationales ou fédérales peuvent prévoir des droits en plus de cette garantie limitée qui ne peuvent être modifiés ou exclus.

Information sur la durabilité écologique

CertainTeed Gypse s'engage envers la durabilité. Situés dans toute l'Amérique du Nord, nos sites de production de produits en gypse couvrent la demande régionale en matériaux et respectent des règles éthiques responsables accordant une grande importance à l'environnement, à la préservation des ressources naturelles, au recyclage et à la gestion des déchets. Nous continuons à rechercher des moyens de réduire l'impact de notre industrie sur l'environnement tout en satisfaisant aux demandes des clients de solutions écologiquement durables qui fournissent confort, protection et performances.

CertainTeed is committed to sustainability and transparency.  CertainTeed Gypsum created 3rd party Type III product and plant specific Environmental Product Declarations (EPDs) for many of our products, including 5/8” Type X, 5/8” M2Tech Type X, ½” Type C, 5/8” Type C, 5/8” GlasRoc Sheathing, 5/8” Extreme Abuse, and 5/8” Extreme Impact.  These Type III EPDs are certified by UL Environment.

CertainTeed Gypsum also has Health Product Declarations (HPDs) for all gypsum board products; many which are 3rd party verified.  The 3rd party verified HPDs provide assurance all the products raw materials are declared to the specified PPM.  PLUS, 3rd party verified HPDs can assist in achieving credits in your LEED v4.1 project. 

CertainTeed Gypsum also is committed to producing low VOC content products.  Many of our gypsum board and setting compounds are GREENGUARD Gold certified through UL Environment. 

Our gypsum board manufacturing facilities, located throughout North America, operate in a responsible and environmentally conscious ethic which includes:

  • Réclamation
  • Préservation des ressources naturelles
  • Le recyclage
    • Many plants have pre and/or post-consumer recycled content used within the products
    • Papier 100 % recyclé sur les deux faces
    • Les déchets en usine sont recyclés dans le processus de fabrication.
  • La gestion des déchets

CertainTeed products can contribute to many different Green Building Rating systems, such as the LEED and WELL programs. Sustainable documentation, including recycled content, EPD’s, HPD’s, VOC Certifications, can be found at https://certainteed.concora.com/.

Distributeurs de produits de finition

Voir tous les distributeurs près de chez vous
Pour commencer
Powered by Translations.com GlobalLink OneLink Software