Rapid Coat® All Purpose Joint Compound is a professional-grade, multi-task joint compound, ideal for use in all phases of drywall finishing: taping, finishing, skim coating, texturing, filling corner beads and trim, and concealing nail or screw dimples.

Designed specifically for professional use, Rapid Coat is premixed and ready to use right out of the container, with a formulation that sands easier than ever. it is ideal for traditional or high performance bead products and performs great for all levels of finish.

Available in 4,5 gallon pail, or 3,5 and 4,5 gallon boxes.

Check out our other Rapid Coat Joint Compound products:

Composé à joints ultra léger Rapid CoatMD
Composé à joints léger Rapid CoatMD
Composé à joints de poids moyen Rapid CoatMD

Présentation du produit

Sélectionnez un filtre et cliquez sur Appliquer pour voir les résultats

Caractéristiques techniques

Information technique

Matériau : Vinyl-type formulation.

Couleur : Blanc

Emissions: Asbestos free.

Couverture : Approximately 120 to 125 pounds per 1 000 square feet. Coverage will depend on the number of beads and amount of trim.

Temps de séchage : Thoroughly dry in approximately 24 hours. Drying times will vary with temperature and humidity (see Gypsum Association [GA] publication 236).

For interior Use Only. For optimal drying, maintain a room temperature of 68 to 77 degrees F (20 to 25 degrees C), and provide adequate ventilation.

Stockage : Up to nine-month shelf life if protected from extreme heat and cold.

Manufactured to conform to ASTM C475.

Caractéristiques techniques

Installation

Apply according to Gypsum Association publications GA-214 and GA-216.

Taping and Finishing Joints:
La première étape : Using a steel finishing knife (4 to 6 inches), generously apply Rapid Coat® All Purpose Joint Compound to the surface to be finished (tapered edge). Next, center and press the joint tape firmly into the compound, removing any excess material behind the tape and creating a good bond with the gypsum board. Allow the compound to dry thoroughly.
Deuxième étape : Using a 10- to 12-inch steel finishing knife or trowel, apply a fill coat of Rapid Coat® All Purpose Joint Compound over the embedded tape. Remove excess material by feathering the center and the edges of the joint. Allow the compound to dry thoroughly.
Troisième étape : Using a 10- to 12-inch steel finishing knife or trowel, applya thin coat of Rapid Coat® Fullweight joint compound over the step two application at a width adequate to fill any voids or shallow spots. Remove excess material by feathering the center and edges of the joint. Allow the compound to dry thoroughly before sanding or painting.

Finishing Inside Corners:
Using a steel finishing knife (4 to 6 inches), generously apply Rapid Coat® All Purpose Joint Compound to both sides of the inside corner. Fold the joint tape along the center crease and press firmly into the center of the inside corner. Remove any excess material behind the tape and create a good bond with the gypsum board. Allow the compound to dry thoroughly. Apply a second coat to one side, allow it to dry, and apply another coat to the opposite side. Allow the compound to dry thoroughly before sanding or painting. Remarque : Rapid Coat® All Purpose Joint Compound is not recommended for use with mesh tape. For mesh tape applications, use Rapid Joint® setting-type compounds.

Fasteners and Trim:
Rapid Coat® All Purpose Joint Compound can be used to fill corner beads and nail/screw dimples. A second coat may be applied, if necessary, when the first coat is dry.

Ponçage ::
Sanding is not required between applications unless the work is rough. Light sanding, after step three above, should be done after the application is thoroughly dry (120- to 150-grit sandpaper or mesh cloth is recommended). Wet sanding is recommended to avoid creating dust.

Skim Coating:
Rapid Coat® All Purpose Joint Compound can be used to skim coat gypsum-board walls. A skim coat leaves a thin film of joint compound over the entire gypsum-board surface, fills imperfections, and eliminates texture differences between the gypsum board and the joint compound. Skim coating is recommended for rooms with critical lighting conditions.

Painting and Wallpapering:
Painting should not proceed until the joint compound is thoroughly dry (see GA-236). For best results, a good-quality gypsum-board primer should be applied, in accordance with the primer manufacturer's instructions, before painting or wallpapering.

Texturing:
Rapid Coat® All Purpose Joint Compound can also be used to texture walls and ceilings. For best results, a good-quality gypsum-board primer should be applied, in accordance with the primer manufacturer's instructions, before texturing. Rapid Coat® All Purpose Joint Compound can then be applied to the dry primer surface up to ¼ inch thick with a roller, sponge, brush, or trowel to create the desired effect. Overpaint when dry in accordance with the paint manufacturer's instructions.

Cleanup:
Rapid Coat® All Purpose Joint Compound washes off easily with warm water. Tools should be dried thoroughly to prevent rusting.

Détails Garantie

Étant donné que les méthodes et les conditions d’application et de stockage, telles que la température, l’humidité et la dilution excessive sont hors de notre contrôle, CertainTeed Gypsum, Inc. (CertainTeed) ne sera pas responsable de la défaillance de ce produit lorsqu’il n’est pas utilisé et stocké conformément aux instructions et spécifications et aux normes de procédure acceptées inhérentes à l’application de cloisons sèches; ou lorsque l’utilisateur ne tient pas raisonnablement compte des conditions météorologiques et de travail défavorables. Cependant, si ce produit s’avère défectueux, la responsabilité maximale de CertainTeed sera limitée au remplacement du matériel défectueux uniquement ou au remboursement du prix d’achat initial. CertainTeed ne sera pas responsable des autres coûts ou dépenses. Il s’agit de la garantie exclusive et des recours fournis par CertainTeed, y compris, sans s’y limiter, les garanties implicites ou la qualité marchande, l’aptitude à l’emploi et l’aptitude à un usage particulier. Tout recours en garantie doit être soumis par écrit à CertainTeed dans les 30 jours suivant la découverte du problème. Les lois nationales ou fédérales peuvent prévoir des droits en plus de cette garantie limitée qui ne peuvent être modifiés ou exclus.

Information sur la durabilité écologique

CertainTeed Gypse s'engage envers la durabilité. Situés dans toute l'Amérique du Nord, nos sites de production de produits en gypse couvrent la demande régionale en matériaux et respectent des règles éthiques responsables accordant une grande importance à l'environnement, à la préservation des ressources naturelles, au recyclage et à la gestion des déchets. Nous continuons à rechercher des moyens de réduire l'impact de notre industrie sur l'environnement tout en satisfaisant aux demandes des clients de solutions écologiquement durables qui fournissent confort, protection et performances.

CertainTeed is committed to sustainability and transparency.  CertainTeed Gypsum created 3rd party Type III product and plant specific Environmental Product Declarations (EPDs) for many of our products, including 5/8” Type X, 5/8” M2Tech Type X, ½” Type C, 5/8” Type C, 5/8” GlasRoc Sheathing, 5/8” Extreme Abuse, and 5/8” Extreme Impact.  These Type III EPDs are certified by UL Environment.

CertainTeed Gypsum also has Health Product Declarations (HPDs) for all gypsum board products; many which are 3rd party verified.  The 3rd party verified HPDs provide assurance all the products raw materials are declared to the specified PPM.  PLUS, 3rd party verified HPDs can assist in achieving credits in your LEED v4.1 project. 

CertainTeed Gypsum also is committed to producing low VOC content products.  Many of our gypsum board and setting compounds are GREENGUARD Gold certified through UL Environment. 

Our gypsum board manufacturing facilities, located throughout North America, operate in a responsible and environmentally conscious ethic which includes:

  • Réclamation
  • Préservation des ressources naturelles
  • Le recyclage
    • Many plants have pre and/or post-consumer recycled content used within the products
    • Papier 100 % recyclé sur les deux faces
    • Les déchets en usine sont recyclés dans le processus de fabrication.
  • La gestion des déchets

CertainTeed products can contribute to many different Green Building Rating systems, such as the LEED and WELL programs. Sustainable documentation, including recycled content, EPD’s, HPD’s, VOC Certifications, can be found at https://certainteed.concora.com/.

Distributeurs de produits de finition

Voir tous les distributeurs près de chez vous
Pour commencer
Powered by Translations.com GlobalLink OneLink Software